Love Letters DIY Necklace

search

Love Letters DIY Necklace

Show your bridesmaids some love with this adorable Love Letters DIY Necklace. Created with embroidery thread, this easy DIY jewelry looks like it came right off the shelves of Anthropologie or Urban Outfitters. It would be an adorable accessory to create for all of your bridesmaids. If you are feeling adventurous, you could even try to craft it with a different word. Creating this necklace to say “bride” would be a great last-minute gift to create for a bridal shower.

Time to complete: In an evening

intermediate

Estimated Cost: $11-$20

Love Letters DIY Necklace

Materials:

  • Craft wire (I used 24 gauge)
  • Embroidery thread, one skein
  • Scissors
  • Round nosed jewelry pliers
  • Chain (length is up to you)
  • Clear nail polish (you'll use this in more than one way!)
  • Jump rings and jewelry clasp (optional)
  • Charm or tassel (optional, not shown)
  • Ruler (not shown)

 

 

Instructions:
1.) Cut a length of wire. About 10 or so inches should be enough. Using the round nosed jewelry pliers, create a look at one end of the wire.
Love Letters DIY Necklace

2.) Keeping the skein of thread in tact/in the packaging (this makes it easier to work with), tightly tie the thread near the loop you just made. Triple or quadruple tie it for extra security.
Love Letters DIY Necklace

3.) Begin tightly wrapping the thread around the wire. I found that it was easier to do this if you hold the entire skein of thread in one hand while wrapping. Be sure to wrap the thread as tight as possible.


4.) Continue wrapping the thread, until you've reached about 9 (or so) inches of wrapped wire.
Love Letters DIY Necklace

5.) Tightly triple or quadruple knot the thread.
Love Letters DIY Necklace

6.) Cut off the excess thread, and secure the knot with clear nail polish. Let dry.
Love Letters DIY Necklace

7.) Cut off the excess wire, leaving about half an inch. Use the pliers to create a loop, just like you did earlier.


8.) Go back to the end that you started with, and cut off the excess thread. Secure with clear nail polish and let dry.
Love Letters DIY Necklace

9.) Start creating the "L" at one end. Bend the wire to the left, like the first picture above. Wrap the wire back over to the right, around the pliers as shown above. This will create the bottom portion of the L.


10.) To make the "O", wrap the wire around the cap of the nail polish bottle. This will help guide the general shape. Remove the bottle and mold the "O" as you wish.


11.) After you're done with the "O", make the sure the wire is bending up, like the first picture above. Sharply bend it back down to begin the "V". Tighten the sharp bend by squeezing it with the pliers.
Love Letters DIY Necklace

12.) Bend the wire back up, then horizontally. This will create the "V".
Love Letters DIY Necklace

13.) Wrap the wire around and over the pliers for the "e".
Love Letters DIY Necklace

14.) Bend the wire back up to complete the last letter.
Love Letters DIY Necklace

15.) Attach the chain to both ends. You can either use jump rings, or simply open up the loops with the pliers. You can also attach the chain to one end of the pendant, so that it hangs differently. It's totally up to you.
Love Letters DIY Necklace

16.) Attach a charm or tassel, if you'd like. I decided to add a vintage gold charm.

 

 

 

 

Your Recently Viewed Projects

Leave a Comment

Rate

Cancel Reply to Comment

Thanks for your comment. Don't forget to share!

Close

Report Inappropriate Comment

Are you sure you would like to report this comment? It will be flagged for our moderators to take action.

Thank you for taking the time to improve the content on our site.

Close Window